1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet:Specifications A414/A414M, A424, A606, A659/A659M, A794, A1008/A1008M, A1011/A1011M, and A1039/A1039M.
ASTM A749 / A749M - 14 Standard Specification for Steel ASTM Standards. A109/A109M Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled. A370 Test Methods and Definitions for Mechanical Testing of Steel Products. A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
ASTM-AISI THICKNESS TOLERANCE RANGES H.R. FLAT H.R. FLAT BAR HOT ROLLED MILD STEEL 3/4x 1 2.550 51.00 1-1/4 3.188 63.76 1-1/2 3.825 76.50 1-3/4 4.463 89.26 2 5.100 102.00 2-1/2 6.375 127.50 3 7.650 153.00 3-1/2 8.925 178.50 Various ASTM Specs for Steel Sheets A366 Cold Rolled Commercial Quality A569 Hot Rolled Commercial Quality A570 Hot Rolled Structural Quality A526 Zinc Coated
Hot-Rolled steel has been rolled at high temperature from a cast steel slab more than two inches thick into steel coil as thin as 1/16 of an inch thick. Because the steel is rolled hot, and the reduction from slab to coil is great, the coil surfaces are noticeably rough and slightly oxidized.
JIS Standard Hot Rolled Channel Steel - SinoSourcesCold Drawn/ Cold Pilfered/ Cold Rolled/ Hot Rolled/ Forged. Other processing service. Hot dip Galvanized, Pre-galvanized, Color Painting, Coated, Cutting, Bending, Punching as long as you can tell us your requirement. Offer Standards. ASTMA53/ASTM A573/ASTM A 283/ASTM A36 BS7-1985/BS EN10025/BS970 GB/T3091-2001, GB/T13793-92, ISO630/E235B/
STANDARD ASTM MILL TOLERANES FLATNESS1/2 or .500 5/8 or .625 3/4 or .725 7/8 or .875 obtained by measuring the difference 1-1/4 or 1.250 between the diagonals of the cut length. The 1-1/2 or 1.500 The Camber Tolerance for coils is one (1) inch to any 20 feet. OUTOFSQUARE Hot Dipped Metallic- oated Sheet Over 12 Inches Wide Not Resquared (ASTM 924/97A)
2.1 ASTM Standards:2 A 370 Test Methods and Denitions for MechanicalTesting of Steel Products A 568/A 568M Specication for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for A 569/A 569M Specication for Steel, Carbon (0.15 Maxi-mum, Percent), Hot-Rolled Sheet and Strip
hot rolled 5mm thickness space spcc - Boiler and Pressure ASTM Standard SPCC Cold Rolled Steel Coil Sheet Thickness hot rolled 5mm thickness space spcc. ASTM Standard SPCC Cold Rolled Steel Coil Sheet Thickness 0.18-3.5mm . Description Cold rolled steel is essentially hot rolled steel that has had further processing. space spcc 1.Thickness 0.15mm-2.5mm 2.Width 800mm-1500mm 3.Inner Diameter 508mm 4 ASTM A635 / A635M - 15 Standard Specification for Steel 1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils. 1.2 It applies to Specifications A414/A414M , A424/A424M , and A1018/A1018M . 1.3 This material is available only in coils described as follows: