Katalor Enterprises is a professional section steel supplier in China , we can supply A283GrA/B/C/D, A36, S235JR, S235J0, S235J2, S275JR, S275JO, S275J2, S355JR Channel steel /beam steel/Square pipe ,and ABA32A36DD32D36 angle steel for shipbuilding.
China Mild Steel Plate Structural Ms - Shandong StandardS355 structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 - 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709.
S235JR is common steel grade in European steel standard specification EN 10025-2 which are mainly used to produce structural parts of the bolted and welded steel in dustrial area.. SS400 in Japan steel specification JIS G3101 is also one mild steel grade.Grade S235JR and SS400 are both common carbon structural steels.Type steel plates are making steel tanks in Oil and gas industry.
EN 1.0038 Steel S235JR Material Equivalent, Properties Dec 14, 2019 · Physical Properties of S235JR Steel (1.0038 Material) Material density:7.85g/cm3; Melting point:1420-1460 °C (2590-2660 °F) S235JR Steel (1.0038 Material) Mechanical Properties. The yield strength, tensile strength, elongation, and Charpy impact test are listed in the following data sheet. EN 1.0038 material Brinell hardness:120 HBW
EN10025 S235JR steel plate standard and specificationThickness:5 200 mm. Width:Up to 3.5 metres wide. Length:Up to 14 metres long. Certification:EN10204 3.1/3.2. Steel Number:1.0038. Delivery Condition:As Rolled or Normalised. Comparison of Steel Grades. S235JR DIN EN 10025-2 Number:1.0037. EN10025:1990.
The mechanical properties of S235JR are presented in Table 5 as the minimum values required for the yield strength, tensile strength as well as for the elongation. These values are also classified according to different thickness of steel sheets. TABLE 5 Mechanical Properties of S235JR Steel (BS EN 10025, 1993) Minimum yield strength ReH [MPa] nominal thickness t [mm] Minimum tensile
S235, S275 and S355 Structural Steels - AZoMFeb 13, 2018 · Structural steel grades are engineered with specific chemical compositions and mechanical properties formulated for specific applications. In Europe, Structural Steel must adhere to the European Standard EN 10025, governed by the European Committee for Iron and Steel Standardization (ECISS), a subset of CEN (European Committee for Standardization).
S235JR - OvakoS235JR:C max 0,20 % for sizes over 40 mm. Only CEV required in standard. SS 1312:Not binding recommendation for Mn (0,4 - 0,7) % in standard
S235JR EN10025-2 Material 1.0037 Steel(id:5195474). View product details of S235JR EN10025-2 Material 1.0037 Steel from Henan Bebon International Co. manufacturer in EC21
S235JR Non-alloy quality structural steel - Material GradesEN 10025 is the European standard for Hot rolled products of structural steels. Additionally it also specifies technical delivery conditions for non-alloy structural steels. Why S235JR called 1.0038 Stainless Steel? S235JR is the EN mechanical and chemical designation stated in the standard whereas 1.0038 is the numeric designation of the same
S235JR Valve,S235JR flanges,S235JR Pipe Fitting,S235JR S235JR angle bars, S235JR flanges, Pipe Fitting, Steel Pipe, Heat Exchanger and Reducer, Gasket, Tee, Pipe Fitting, Tube Plate, have all specifications. With many yeas production experience, strict control S235JR chemical composition and S235JR mechanical properties.
Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235JR Round Bar S235JR Flat Bar S235JR Hollow Bar S235JR Tube / Pipe S235JR Sheet / Plate S235JR Strip / Coil S235JR Wire S235JR Forging S235JR Tube / Pipe TEL:+86-80247006
S355J2(+N) / 1.0570(dubl) - SteelNumber - Chemical C :Si :Mn :Ni:P:S:Cr:Mo:Al - max 0.22:max 0.55:max 1.6:max 0.3:max 0.035:max 0.035:max 0.3:max 0.08:max 0.02:Cr+Mo+Ni :0.048
Steel Grades, Properties and Global Standards4 - Steel Grades, Properties and Global Standards *designation according to Stahl Eisen Liste (Register of European Steels). 1also available as EDX 2304 with enhanced properties.2also available as S31803. 3724L is a modifies version of 4435 for Urea applications.4317LMN not available in all product forms.5also available as N08367.6also available as 317L with
Steel rod, bars and wire for cold heading and cold extrusion EN 10265:Magnetic materials. Specification for steel sheet and strip with specified mechanical properties and magnetic permeability EN 10267:Ferritic-pearlitic steels for precipitation hardening from hot-working temperatures EN 10268
UPN (UNP) European standard U channels, UPN steel UPN (UNP) European standard U channels, UPN steel profile specifications, dimensions, properties. Current table represents European standard U (UPN, UNP) channels, UPN steel profile (UPN beam), specifications, properties, dimensions. Manufactured according to standards :DIN 1026-1:2000, NF A 45-202:1986; EN 10279:2000 (Tolerances)
productinformation precidur S235JR - thyssenkruppMaterial name:S235JR / S235J0 / S235J2 Proprietary brand:® precidur S235JR /J0 /J2 Old name:St 37-2 Delivery specification:DIN EN 10025-2 Application:Steels for general mechanical engineering and steel structures with physical properties in accordance
Chemical composition of S235JR steel plate C0.17 Si0.35 Mn0.65 P0.030 S0.030. Mechanical properties of S235JR steel plate Yield strength225 Tensile strength 360510 Elongation18 S235JR steel plate is equivalent to the national standard Q235B. Surface classification of S235JR steel plate Normal surface (FA)